How to Run the KitchenAid Dishwasher Diagnostic Mode

If you suspect that your KitchenAid dishwasher may be experiencing issues, you’re in the right place. Running the KitchenAid dishwasher diagnostic mode can help identify any problems, and the process varies depending on your dishwasher model.

You can run a diagnostic on your KitchenAid dishwasher by using specific key combinations depending on your model. For example, you can press Heated Dry + Normal (twice), High Temp Wash (6 times) + Start (once), Keys 1, 2, and 3 (thrice), Rinse Only + SANI (twice), High Temp Scrub + Air Dry (twice), or High Temp Wash + Energy Saver Dry (twice).

There are multiple methods to reset the dishwasher, but the key factor is the specific model you own. After completing the diagnostic process, it’s crucial to take note of any error codes that appear on the dishwasher’s display.

In this article, we’ll guide you through the various steps required to initiate the diagnostic mode on your KitchenAid dishwasher. Additionally, we’ll delve into the world of KitchenAid dishwasher error codes, as the primary objective of running a diagnostic is to identify these codes and understand their meaning. This knowledge will enable you to address the issues with your dishwasher and ultimately clear any error codes that may be present.

KitchenAid dishwasher diagnostic mode

Easy Guide to Run the KitchenAid Dishwasher Diagnostic Mode

Diagnostic Mode ShortcutPreferred Dishwasher Model
Press Heated Dry – Normal – Heated Dry – NormalW10142800B, 8572216, W10130990C
Press High Temp Wash (6 Times) + StartKUDD03DT
Press Keys 1, 2, 3, 1, 2, 3, 1, 2, 3W10195615A
Press Rinse Only – SANI Rinse – Rinse Only – SANI RinseKIDS01EK
Press High Temp Scrub – Air Dry – High Temp Scrub – Air Dry8537797
Press High Temp Wash – Energy Saver Dry – High Temp Wash – Energy Saver DryKUDR245EWH5

How to Enter Diagnostic Mode On KitchenAid Dishwasher

Here are the different methods you can use to activate the diagnostic mode on your KitchenAid dishwasher, each tailored to your specific dishwasher model.

1. For KitchenAid W10142800B, or 8572216 or W10130990C Dishwashers

If you own one of the KitchenAid dishwashers, models W10142800B, 8572216, or W10130990C, and need to activate the service mode, follow these simple steps:

  1. Ensure your dishwasher is in standby mode (plugged in but not powered on) if it’s not already.
  2. Locate the Heated Dry and Normal cycle buttons.
  3. Quickly press these buttons in the following sequence: Heated Dry, then Normal.
  4. Repeat the sequence by pressing Heated Dry and Normal again, in the same order. This action will place your dishwasher into service mode.

It’s important to perform these steps swiftly, within 6 seconds, once you confirm that your dishwasher is in standby mode. Additionally, for the KitchenAid 8572216 dishwasher, you have an alternative method of entering service mode by unplugging its thermistor twice after disconnecting the user interface.

2. For KitchenAid KUDD03DT Dishwashers

To put your KitchenAid KUDD03DT dishwasher into diagnostic mode, follow these straightforward steps:

  1. Start with your dishwasher in standby mode.
  2. Locate the ‘High Temp Wash’ key and press it six times consecutively.
  3. Afterward, press the ‘start’ button to enter service mode.

It’s crucial to complete these steps within 10 seconds, so be sure to act swiftly when initiating the service mode. Additionally, ensure that you run this test with clean water to ensure accurate sensor functionality.

Here are some essential notes to keep in mind when conducting this test:

  • If there’s an error code, the ‘cancel’ LED light will flash.
  • Before pressing any key after the Cancel LED flashes with an error code, make sure to note the fault code.
  • If you need to pause the sequence during the test, simply open the dishwasher door. To resume, close the door. These tips will help you effectively navigate the diagnostic process for your KitchenAid KUDD03DT dishwasher.
How do I run a diagnostic on my dishwasher

3. For KitchenAid W10195615A Dishwashers

If you own a KitchenAid W10195615A dishwasher and need to activate its diagnostic mode, follow these simple steps:

  1. Start by putting the dishwasher in standby mode.
  2. Quickly press the first three keys in sequence: keys 1, 2, and 3.
  3. Repeat the action by pressing these three sets of keys again, with a one-second interval between each press.
  4. Finally, press the three keys one last time to initiate the KitchenAid Dishwasher diagnostic mode.

Keep in mind that your dishwasher will only begin the test once you close its door, so ensure that you’ve done this before pressing the cycle keys. Following these steps will help you effectively access the diagnostic mode for your KitchenAid W10195615A dishwasher.

Related: KitchenAid Dishwasher Touchpad Not Working

4. For KitchenAid KIDS01EK Dishwashers

To activate the service mode on your KitchenAid KIDS01EK dishwasher, follow these straightforward steps:

  1. Begin by ensuring that your dishwasher is in standby mode.
  2. Swiftly press the Rinse-Only and SANI Rinse Keys.
  3. Repeat the action by quickly pressing Rinse-Only and SANI Rinse once again. This will enter the KitchenAid dishwasher diagnostic mode.
  4. Now, patiently wait for your dishwasher to display any error codes if present.

Following these steps will allow you to easily access the diagnostic mode for your KitchenAid KIDS01EK dishwasher.

5. For KitchenAid 8537797 Dishwashers

To activate the service mode on your KitchenAid 8537797 dishwasher, follow these straightforward steps:

  1. Start with the dishwasher in standby mode.
  2. Press the High-Temp Scrub button.
  3. Quickly follow this by pressing the Air Dry switch.
  4. Press both the High-Temp Scrub and Air Dry buttons one more time.

It’s worth noting that you have some flexibility in the button choices. Instead of High Temp-Scrub, you can use High-Temp Scour or Power Scour, and for Air Dry, Energy Saver Dry or No Heat Dry can be substituted. The dishwasher will enter service mode regardless of the specific buttons you choose.

As an alternative method, you can initiate the KitchenAid dishwasher diagnostic mode by pressing SANI Rinse and Air Dry if your dishwasher doesn’t have SANI Rinse, use Energy Saver Dry or No Heat Dry instead. These options offer you flexibility in accessing the diagnostic mode for your KitchenAid 8537797 dishwasher.

kitchenaid dishwasher diagnostic codes

6. For KitchenAid KUDR245EWH5 Dishwashers

To perform diagnostics on your KitchenAid KUDR245EWH5 dishwasher, follow these simple steps:

  1. Begin with your dishwasher in standby mode.
  2. Press High-Temp Wash + Energy Saver Dry keys on your dishwasher.
  3. Quickly repeat the action by pressing these two keys again, making sure to complete everything within 10 seconds.

As an alternative, you can press High-Temp Wash three times instead of twice, but remember that all actions must take place within the 10-second window. These steps provide a straightforward way to access the diagnostic mode for your KitchenAid KUDR245EWH5 dishwasher.

KitchenAid Dishwasher Diagnostic Codes

When you run diagnostics on your dishwasher, it can reveal error codes that provide valuable information about potential issues. To help you navigate these codes, here’s a table that breaks down the different diagnostic error codes for KitchenAid dishwashers:

Certainly, here’s a unique table with the same data for your website:

Error CodeInterpretation/MeaningRecommended Action
Flashing All Cycle Buttons or OptionsIndicates an unlatched doorMake sure to securely close the dishwasher door and then perform a dishwasher reset.
Flashing Clean LightSignals issues like disconnected water supply, a stuck overfill protection float, or excessive sudsEnsure that the water supply is properly connected. Try pressing down the overfill protection float. Additionally, reduce the detergent amount and reset the dishwasher.
Control Lock (Red Indicator)Indicates that the Control Lock is ONDisable the Control Lock by pressing and holding the appropriate buttons for 3 seconds.
Blinking/Flashing LightsCan result from an open door, power interruption, or a Delay Start settingClose the dishwasher door if it’s open, verify that the dishwasher has a stable power supply, and disable the Delay Start setting if enabled. Then, reset the dishwasher.
Flashing Rinse-Only LightPoints to stuck keysGently press any stuck keys to release them and then reset the dishwasher.
Flashing Sanitize LightIndicates unsanitized dishes due to incorrect sanitization temperatureAdjust the sanitization temperature to a minimum of 49°C/120°F, and then reset the dishwasher.
F1E1/CODE 1-1Suggests a stuck relayAttempt to reset the dishwasher, and if the issue persists, consider replacing the Electronic Control Board (ECB).
F1E2/CODE 1-2Indicates a problem with the ECB memoryReset the dishwasher to clear this error code.
F2E1/2-1, F3E1/3-1, or F383/3-3Suggests issues with control panel keys, either stuck or faultyInspect the control panel buttons for sticking keys. If any are found to be faulty, consider professional assistance or replacement.
F4E3Suggests the dishwasher needs to be resetPerform a dishwasher reset to resolve this issue.
F2E2 (CODE 2-2)Indicates a need to reset the dishwasherExecute a dishwasher reset to address this error code.
F6E3Attributed to excess suds or the use of the wrong detergentUse the correct detergent, avoid overfilling, and maintain proper detergent usage.
F6E4Suggests an unlevelled dishwasherProperly level the dishwasher to ensure it operates correctly.
F10E5/FAE5Indicates a completed cycleCancel the current dishwasher cycle, if necessary, and start a new one as needed.
F6E1Indicates the dishwasher won’t startExecute a dishwasher reset to address this issue.
F8E4Suggests incorrect dishwasher installationReview the dishwasher’s installation instructions to ensure proper installation.
F8E5Relates to the dishwasher’s drain sequenceVerify that the dishwasher’s water supply is turned on, or turn off the dishwasher to resolve this error.
CODE H2OPoints to a failed water supplyCheck and ensure that the water supply tube is properly connected and free from obstructions.

How to Reset KitchenAid Dishwasher?

As you may have discovered, performing a reset on your KitchenAid dishwasher can be a powerful solution for addressing various issues. A reset not only clears KitchenAid dishwasher error codes but also refreshes the dishwasher’s memory, cancels running cycles, and can rectify malfunctions. Here are three effective ways to reset your KitchenAid dishwasher:

Option 1 (Basic Reset):

The basic reset is a versatile method to refresh your dishwasher’s memory and clear most error codes. Begin by turning off the dishwasher’s circuit breaker and unplugging it from the power source for 5–10 minutes. After this brief pause, turn the circuit breaker back on, plug in the dishwasher, and power it up. You should find that the error code has disappeared.

Option 2 (Control Panel Reset):

The control panel reset is particularly useful when dealing with KitchenAid dishwasher control panel related issues or when your dishwasher experiences unexplained malfunctions, such as failing to start. To execute this reset, locate the Dry and High Temp buttons on your dishwasher and press them 5–10 times. Ensure that you securely close the dishwasher door during this process.

Option 3 (Cycle Reset):

When you need to cancel an ongoing cycle and initiate a new one, the Cycle Reset comes in handy. Simply identify the Drain or Cancel button and press and hold it for several seconds. This action will terminate the current cycle. Afterward, close the dishwasher door and start a new cycle to resolve the issue.

How to Run the KitchenAid Dishwasher Diagnostic Mode

Frequently Asked Questions

1. How to solve KitchenAid dishwasher error codes e1 f9?

To resolve KitchenAid dishwasher error codes E1 and F9, start by checking for blockages in the water inlet valve, drain pump, and hoses. Ensure a proper water supply with no kinks in the water line. If the issue persists, perform a dishwasher reset by turning off the circuit breaker or unplugging it for a few minutes. If the error continues, consult the manual or seek professional help.

2. How Do I Run a Diagnostic On My Dishwasher?

Each dishwasher model may have its unique method to enter diagnostic mode on KitchenAid dishwasher. The best source for this information is your dishwasher’s user manual. If you’re unsure about the process or can’t find the manual, don’t hesitate to reach out to your dishwasher manufacturer for guidance. They can provide you with specific instructions tailored to your dishwasher model, ensuring you can run diagnostics effectively and address any potential issues.

3. Why Is My KitchenAid Dishwasher Not Working?

If your KitchenAid dishwasher isn’t starting, it could be due to several factors. Common culprits include the dishwasher being in Sleep Mode, having a Delayed Wash setting, or the Control Lock being activated. To get your dishwasher up and running, it’s essential to deactivate any of these three settings. Once you’ve cleared these obstacles, your dishwasher should be ready to operate smoothly.

4. How can I find the error code on my KitchenAid dishwasher?

To identify an error code on your KitchenAid dishwasher, utilize the KitchenAid Dishwasher diagnostic mode. Once you’ve initiated this mode, refer to your user manual to decipher the meaning of the error codes and discover the recommended solutions to address the issue. This straightforward process allows you to effectively diagnose and resolve any problems with your dishwasher.

5. Why is my KitchenAid dishwasher keep stopping?

If your KitchenAid dishwasher frequently stops mid-cleaning cycle, the culprit may be a tripped circuit or a potentially malfunctioning motor. Over time and with regular use, dishwasher components can wear out or become damaged. It’s advisable to perform routine inspections to ensure all parts are in good condition. Should you identify a faulty motor, consider having it replaced to maintain your dishwasher’s optimal performance and uninterrupted cleaning cycles.

Final Words on KitchenAid Dishwasher Diagnostic Mode

Understanding how to navigate your KitchenAid dishwasher diagnostic mode and error codes empowers you to troubleshoot and maintain your appliance effectively. Whether it’s resetting the dishwasher, deciphering error codes, or addressing common issues, these insights ensure your dishwasher runs smoothly, saving you time and potential repair costs. Keeping your dishwasher in top shape is the key to consistently sparkling, hassle-free dishwashing.

Similar Posts

Leave a Reply

Your email address will not be published. Required fields are marked *